Using the ImageMosaic plugin with footprint mangement

Introduction

This step-by-step tutorial describes how to associate Footprint to a raster data using the ImageMosaic plugin.

Footprint is a Shape used as a Mask for the mosaic. Masking can be useful for hiding pixels which are meaningless, or for enhancing only few regions of the image in respect to others.

This tutorial assumes knowledge of the concepts explained in Using the ImageMosaic plugin.

This tutorial contains two sections:

  • The first section, Configuration, describes the possible configurations needed to set up an ImageMosaic with footprint.
  • The second section, Examples, provides examples of configuration of an ImageMosaic with footprint.

Configuration

Footprint can be configured in three different ways:

  1. By using for each mosaic granule a Sidecar File, a Shapefile with the same name of the granule which contains the footprint for it;
  2. By using a single Shapefile called footprints.shp which contains all the footprints for each granule; each footprint is associated to a granule with the location attribute;
  3. By using a file called footprints.properties .

The last option should be used when the first two are not available and requires to write the following piece of code inside the footprints.properties file:

footprint_source=*location of the Shapefile*
footprint_filter=*filter on the Shapefile searching for the attribute associated to each granule*

For example if a Shapefile called fakeShapeFile stores the various footprints in a table like this, where each Name attribute is referred to a granule file:

../../_images/shp_table.png

And the associated granules are:

  • ortho_1-1_1n_s_la087_2010_1.tif
  • ortho_2-2_1n_s_la075_2010_1.tif
  • ortho_1-1_1n_s_la103_2010_1.tif
  • and so on ...

The associated footprints.properties file must be like this:

footprint_source=fakeShapeFile.shp
footprint_filter=Name=strSubstring(granule.location, 0, strLength(granule.location) - 4)

The substring operation is done for comparing the footprint attribute names and the granule names without the .tif extension.

There are three possible behaviours for Footprint:

  • None: simply doesn’t use the Footprint and behaves like a standard ImageMosaic layer;
  • Transparent: adds an alpha band of 0s on the image portions outside of the Footprint making them transparent, typically used for RGB data;
  • Cut: set the background value on the image portions outside of the Footprint, typically used for GrayScale data.

The behaviour must be set directly on the Layer configuration page.

Another feature of the Footprint is the possibility to calculate an Inset of the image. Inset is a reduction of the footprint border by a value defined by the user which is typically used for removing the compression artifacts. This feature can be achieved by adding the following code inside footprints.properties (in case of the first two configurations this file must be added):

footprint_inset=*value in the shapefile u.o.m.*
footprint_inset_type=*full/border*

Full inset type calculates the inset for each footprint side while Border does the same operation but those straight lines that overlap the image bounds are avoided; this last parameter is useful for images already cut in a regular grid.

Each modification of the footprints.properties file requires to Reload GeoServer. This operation can be achieved by going to Server Status and cliking on the Reload button on the bottom-right side of the page.

The two datasets used in the tutorial can be downloaded here: Mosaic with a single image which represents Boulder (Colorado), Mosaic with multiple images which represents Italy. The first can be used for testing footprint configuration with a Sidecar File and the second for the other two configurations.

Examples

Here are presented a few steps for configuring a new ImageMosaic layer with footprint.

Step 1: Create a new ImageMosaic Layer

As seen before an ImageMosaic data store can be created by going to Stores ‣ Add New Store ‣ ImageMosaic.

../../_images/imagemosaicconfigure2.png

An associated Layer can be created by going to Layers ‣ Add New Resource, choosing the name of the data store created above and then clicking on the publish button.

Step 2: Configuring a new Layer for the Mosaic

Inside the new page the only field which is interesting for this tutorial is FootprintBehavior:

../../_images/footprint_behav.png

The user can set one of the three values for the Footprint behaviour as described above.

After that, the user must confirm the modification by clicking on the Save button on the bottom side of the page.

Step 3: Example Results

Here are presented the results for each dataset.

Footprint configured with Sidecar File

This is an example of mosaic without applying Footprint:

../../_images/footprint_normal.png

And this is the result of setting FootprintBehavior to Cut:

../../_images/footprint_cut.png

Background is gray because in this example the BackgroundValues field has been set to -20000.

If an Inset is added, the final mosaic is:

../../_images/footprint_cut_inset.png

The footprints.properties file is:

footprint_inset=0.01
footprint_inset_type=full

Note

Remember that each modification on footprints.properties requires a Reload of GeoServer for seeing the results.

Note

When configuring this mosaic you must set the declared CRS field to “EPSG:4326”.

Footprint configured with footprints.shp

This is another example of mosaic without Footprint:

../../_images/footprint_mosaic_none.png

And now after setting FootprintBehavior to Transparent (no Inset is used) on the Layer:

../../_images/footprint_mosaic.png

Footprint configured with footprints.properties

Note

For testing this functionality the user must rename all the footprints.xxx files to mask.xxx.

The result of setting FootprintBehavior to Transparent, Inset type to border and Inset value to 0.00001 is:

../../_images/footprint_mosaic_prop.png

The footprints.properties file is:

footprint_source=mask.shp
footprint_inset=0.00001
footprint_inset_type=border

Raster Masking

From 2.8.x version, GeoServer is able to support also Raster Masks. Those masks can be internal or external, adding the .msk extension to the file name, for each file. Those files also should have the same size as the image they are masking.

It must be pointed out that external/internal masks may have overviews like the related original images.

More information about Mask bands may be found at the GDAL Mask Band Page

Note

Raster masking is supported for GeoTiff format only and it does not take into account inset definition.

Below you may find an example of configuring a Mosaic with Raster masks:

Step 1: Create a new ImageMosaic Layer

Download data from the following link and configure an ImageMosaic layer called rastermask without changing default configuration parameters.

Zip file contains two images and their related .msk files. For this example the two masks are two simple squares.

Step 2: Watch the layer using LayerPreview

Go to LayerPreview ‣ rastermask ‣ OpenLayers. The result should be similar to the one below.

../../_images/footprint_none.png

Step 3: Change the Footprint Behavior

Change the FootprintBehavior parameter to Transparent. Cut value should not be used since the files are RGB.

../../_images/footprint_transparent_setting.png

Step 4: Check the result

Go to LayerPreview ‣ rastermask ‣ OpenLayers. The result should be changed now.

../../_images/footprint_transparent.png